ABS Motorcycle (AM) | Motorcycle
Repair BMW Motorcycle ABS Control Unit ABS I, ABS III | RH-Type AM01 | RH-Type AM01
from 999.00 EUR
Plus 19% VAT,
plus shipping costs.
Repair time:
➜ Express repair: 10-12 working days plus shipping
(+100.00 EUR) ➜ Normal repair time: 20 - 30 working days plus shipping. Devices are processed according to the date of receipt
(no extra charge)
(+100.00 EUR) ➜ Normal repair time: 20 - 30 working days plus shipping. Devices are processed according to the date of receipt
(no extra charge)
Scope of repair:
✶Repair variant 1 base:
Cleaning / repair / overhaul with new pressure sensors / seals etc.
(no extra charge)
Cleaning / repair / overhaul with new pressure sensors / seals etc.
(no extra charge)
✶✶Repair variant 2 pump motor:
Cleaning / repair / overhaul with new pressure sensors / seals etc. andreconditioned replacement pump motors (if possible)
(+200.00 EUR)
Cleaning / repair / overhaul with new pressure sensors / seals etc. and
(+200.00 EUR)
🛈Additional costs of €275.00 net / €327.25 gross may arise in the rare case that the control electronics ECU is damaged, e.g. by water, brake fluid, short circuit, etc. This affects approximately 3% of the repairs we carry out.
Part no.:
FTE, BMW Motorrad ABS III Nr.: FTE S2AB90036
FTE S2AB90037
FTE S2AB90038
FTE S2AB90039
FTE S2AB90040 and others
OEM 34517728059
34517698296
Installed in the following vehicle brands:
BMW
Models:
All BMW motorcycles with Integral and Partial Integral ABS III ( approx. 2000-2006 ) R1100S, R1150R
RS
RT
GS, K1200RS
GT
LT
CL, R1200C
Montauk, R1200GS
ST, K1200R
Device manufacturer:
FTE
Errors:
➜ 1. or 2. brake circuit fault
➜ pressure errors
➜ continuous operation of a hydraulic motor
➜ Failure of brake booster or brake circuit
➜ Failure of brake light
➜ no diagnosis possible etc.
Error code "internal Errors":
➜ 8 Control unit internal error
Error code "Brake pressure":
➜ 25 Rear brake pressure Pressure too low
Fehlercodes "Bremslicht", "Bremsflüssigkeitsstand", "Brake switch":
➜ 245 Front brake switch
Fehlercodes "Druckmodulator", "Pump motor" and further:
➜ 11 Pressure modulator pump motor
➜ 15 Variant coding invalid
➜ 127 System voltage
➜ 133 Speed signal
➜ 135 System fault
➜ 250 Warning lamp relay
➜ 251 ABS warning lamp
➜ 255 System voltage
➜ C2177 Rear ABS pump motor
➜ C224D ABS control unit
➜ 431E Wheel circuit pressure too high, front wheel brake
➜ 440B Rear ABS pump motor
➜ 441E Pressure too high in rear wheel circuit
➜ 00431 ABS control unit
➜ 00430F ABS coding error
➜ 00441 Rear wheel circuit
➜ 00431 Front wheel circuit
➜ 00440B Rear pump motor pressure modulator
➜ 0045FB ABS warning lamp
➜ 004419 Rear wheel circuit
➜ 25166 Power supply
➜ 24951 Rear ABS motor
➜ 4311 Front ABS motor defective
➜ 06234 ABS internal defect
➜ 006186 Rear wheel circuit
➜ 00618A Front wheel circuit
➜ 006177 Pressure modulator pump motor
Installation instructions:
Please remove the accessories from the device. (holders, hoses, etc.) Empty the brake fluid reservoir (turn the appliance upside down and allow it to drain). Wrap the unit in an absorbent cloth and protect the appliance plug from damage and brake fluid. When reinstalling, use new gaskets and clips for the brake line quick-release fasteners (available on the right side of ACCESSORIES).
Standard Lieferung:
Shipping within Germany over KG + packaging
Warranty:
By law. 12/24 month. Warranty extension not available.
Recommended accessories
RH type EZM01 Rubber buffer AM01
9.95 EUR
Zzgl. 19% MwSt., zzgl. Versandkosten
RH-Type EZM02 Mounting kit AM01
24.95 EUR
Zzgl. 19% MwSt., zzgl. Versandkosten
YOU MIGHT ALSO BE INTERESTED IN
Accessories and recommended items from our shop
